* Estimated delivery times start from the date of shipment, excluding processing time.
* Actual delivery times may vary due to holidays, weather conditions, or customs delays.
Livrare standard gratuită pentru comenzi peste $9.9
Politică de returnare
Articolele returnate vor fi acceptate în termen de 40 de zile de la data primirii mărfurilor. Articolele personalizate nu pot fi returnate sau schimbate. Articolele cumpărate cu un card cadou electronic pot fi schimbate doar; rambursările nu se aplică.
Cadou gratuit
Bine ați venit la Roymall, site-ul dumneavoastră profesional pentru achiziționarea de cadouri premium de la magazinele universale. Apreciem și valorizăm sprijinul dumneavoastră și dorim să vă exprimăm recunoștința prin adăugarea unui plus de entuziasm la achizițiile dumneavoastră. Când cumpărați de la noi, nu numai că vă bucurați de produse de înaltă calitate care vă îmbunătățesc stilul de viață, dar veți primi și un cadou gratuit exclusiv cu fiecare comandă pe care o plasați. Sunteți gata să explorați colecția noastră și să găsiți cadourile perfecte pentru dumneavoastră? Răsfoiți selecția noastră de articole premium de la magazinele universale, plasați comanda și așteptați cu nerăbdare entuziasmul primirii cadoului gratuit împreună cu achiziția dumneavoastră.
Politica de livrare
Vom depune eforturi pentru a vă livra articolele după primirea comenzilor dumneavoastră și pentru a ne asigura că acestea ajung în siguranță. Detaliile de livrare vor fi furnizate în e-mailul de confirmare.În majoritatea cazurilor, comenzile sunt procesate în termen de 2 zile.În circumstanțe speciale, acestea vor fi amânate după cum urmează: Când plasați o comandă sâmbătă, duminică sau în zilele de sărbătoare, aceasta va fi amânată cu 2 zile..În mod normal, sunt necesare 5-7 zile lucrătoare (de luni până vineri) fără a fi afectate de întârzieri de zbor sau alți factori de mediu..Deoarece serviciul nostru de livrare este la nivel mondial, timpii de livrare vor depinde de locația dumneavoastră, așa că poate dura ceva timp și vă rugăm să aveți răbdare dacă vă aflați în zone îndepărtate sau țări.
1. Politica de returnare & schimb
Acceptăm doar articole achiziționate de pe roymall.com. Dacă achiziționați de la distribuitorii noștri locali sau de la alți comercianți, nu le puteți returna la noi.Articolele de vânzare finală sau cadourile gratuite nu sunt acceptate pentru returnare.Pentru a fi eligibil pentru returnare, articolul dumneavoastră trebuie să fie nefolosit și în aceeași stare în care l-ați primit. De asemenea, trebuie să fie în ambalajul original.După primirea instrucțiunilor de returnare de la noi, vă rugăm să ambalați articolele returnate și să lăsați pachetul la oficiul poștal local sau la alt curier. Vom procesa articolul returnat sau schimbat în termen de 3-5 zile lucrătoare după ce îl primim. Rambursarea va fi procesată și creditată automat către metoda originală de plată.Nu se pot accepta returnări sau schimburi dacă produsul a fost produs la comandă, inclusiv dimensiuni personalizate, culoare personalizată sau imprimare personalizată.Ai nevoie de mai mult ajutor, te rugăm să ne contactezi. service@roymall.com sau Whatsapp: +8619359849471
2.Politica de rambursare
Veți primi o rambursare completă sau un credit de magazin de 100% după ce primim pachetul returnat și îl verificăm. Rambursarea va fi procesată și creditată automat către metoda originală de plată.Vă rugăm să rețineți că costurile de expediere și orice taxe sau taxe nu sunt rambursabile. Costurile suplimentare de expediere nu sunt rambursabile odată ce pachetul a fost expediat. Sunteți responsabil pentru plata acestor taxe și nu putem renunța la ele sau le rambursăm, chiar dacă comanda este returnată către noi.După ce am primit și am confirmat articolul returnat, vă vom trimite un e-mail pentru a vă anunța că am primit articolul returnat. De asemenea, vă vom anunța despre aprobarea sau respingerea rambursării dumneavoastră.Dacă aveți probleme legate de procesul de rambursare, vă rugăm să ne contactați. service@roymall.com sau Whatsapp: +8619359849471
MAX7219 Microcontroller 4-in-1 Display Dot Matrix Module For
Specifications:
A single module can drive a 8x8 dot matrix common cathode Working voltage: 5V Module size: 12.8 x 3.2 x 1.3 cm (L*W*H) With 64 fixing screw holes, hole diameter: 3mm Module with input and output interfaces, support for cascading multiple modules
Wiring:
1. The left side of the module is the input port, and the right is the output port. 2. Control of a single module, the input port only need to receive CPU. 3. The more a module cascade and input end of the first module is connected with the CPU and input end of the input end of the output end is connected to the second module, output terminal of the second module connected with the three modules, and so on. For example: 51 SCM VCC→5V GND→GND DIN→P2.2 CS →P2.1 CLK→P2.0
Package included:
1 x MAX7219 Dot Matrix Module 1 x 5pin Dupont Cable
I first tried the dotMatrix on the Arduino with the Sprite and Matrix libraries. I got funny results because the column adressing is reversed.
Therefore I switched to the MD_MAX72xx libraries. Make sure to change the define in the MD_MAX72xx. h file to read:
#define USE_FC16_HW 1
I used the MD_Keyswitch library found at https://github.com/MajicDesigns/MD_KeySwitch
and the MD_MAX72xx library found at https://github.com/MajicDesigns/MD_MAX72XX
Then I pulled the source at https://github.com/MajicDesigns/MD_MAX72XX/blob/master/examples/MD_MAX72xx_ScrollChart/MD_MAX72xx_ScrollChart.ino
With that you should be able to get it to work.
If you use pins that are not-SPI standard, make sure to activate the call to MD_MAX72XX with four parameters, and comment out the one with two parameters.
I first tried the dotMatrix on the Arduino with the Sprite and Matrix libraries. I got funny results because the column adressing is reversed.
Therefore I switched to the MD_MAX72xx libraries. Make sure to change the define in the MD_MAX72xx. h file to read:
#define USE_FC16_HW 1
I used the MD_Keyswitch library found at https://github.com/MajicDesigns/MD_KeySwitch
and the MD_MAX72xx library found at https://github.com/MajicDesigns/MD_MAX72XX
Then I pulled the source at https://github.com/MajicDesigns/MD_MAX72XX/blob/master/examples/MD_MAX72xx_ScrollChart/MD_MAX72xx_ScrollChart.ino
With that you should be able to get it to work.
If you use pins that are not-SPI standard, make sure to activate the call to MD_MAX72XX with four parameters, and comment out the one with two parameters.
I first tried the dotMatrix on the Arduino with the Sprite and Matrix libraries. I got funny results because the column adressing is reversed.
Therefore I switched to the MD_MAX72xx libraries. Make sure to change the define in the MD_MAX72xx. h file to read:
#define USE_FC16_HW 1
I used the MD_Keyswitch library found at https://github.com/MajicDesigns/MD_KeySwitch
and the MD_MAX72xx library found at https://github.com/MajicDesigns/MD_MAX72XX
Then I pulled the source at https://github.com/MajicDesigns/MD_MAX72XX/blob/master/examples/MD_MAX72xx_ScrollChart/MD_MAX72xx_ScrollChart.ino
With that you should be able to get it to work.
If you use pins that are not-SPI standard, make sure to activate the call to MD_MAX72XX with four parameters, and comment out the one with two parameters.
very good product and good price.
If you don't know how that work i found one good tutorial.
https://www.makerguides.com/max7219-led-dot-matrix-display-arduino-tutorial/
If you try the programs and see that they do not work with the first one.
Try changing the names of the pins you will use and reload the program on Arduino.
e.g.
CS_PIN 10
DATAPIN 11
CLK_PIN 13
very good product and good price.
If you don't know how that work i found one good tutorial.
https://www.makerguides.com/max7219-led-dot-matrix-display-arduino-tutorial/
If you try the programs and see that they do not work with the first one.
Try changing the names of the pins you will use and reload the program on Arduino.
e.g.
CS_PIN 10
DATAPIN 11
CLK_PIN 13
very good product and good price.
If you don't know how that work i found one good tutorial.
https://www.makerguides.com/max7219-led-dot-matrix-display-arduino-tutorial/
If you try the programs and see that they do not work with the first one.
Try changing the names of the pins you will use and reload the program on Arduino.
e.g.
CS_PIN 10
DATAPIN 11
CLK_PIN 13
Tips:For questions about your order, place of delivery, product discount, taxation, delivery time, warranty, shipping, payment, exchange rate, and other questions unrelated to the product, please contact customer service.
@***** look it up in the MAX7219 datasheet. Another cool thing about these ICs is the need for just one resistor to limit the current for all segments x digits (64 per IC) to retain the same brightness whether only one LED is on or all 64. IIRC there's a chart there with recommended resistor values depending on number of LEDs. I could probably lift one of the 8x8 matrices off and see what resistor value they've used, but the datasheet should give you an idea. Assume you need an external power supply though. They're not super bright but it's still 256 LEDs.
@***** look it up in the MAX7219 datasheet. Another cool thing about these ICs is the need for just one resistor to limit the current for all segments x digits (64 per IC) to retain the same brightness whether only one LED is on or all 64. IIRC there's a chart there with recommended resistor values depending on number of LEDs. I could probably lift one of the 8x8 matrices off and see what resistor value they've used, but the datasheet should give you an idea. Assume you need an external power supply though. They're not super bright but it's still 256 LEDs.
Answered by BG344213471 on 31/08/2022Helpful (0)
0
Q:
Can I daisy chain several of these? By just connecting output of the first with input of the next?
Can I daisy chain several of these? By just connecting output of the first with input of the next?
Depending on how much you want to daisy chain you should inject supply power every 2 or 3 modules else the voltage drop and the current running through the modules gets to high
Depending on how much you want to daisy chain you should inject supply power every 2 or 3 modules else the voltage drop and the current running through the modules gets to high
Depends on what you mean by "users manual". The datasheet for the MAX7219 controller is excellent and all you need to know to program these things. If you want plug and play there are multiple libraries to choose from.
Depends on what you mean by "users manual". The datasheet for the MAX7219 controller is excellent and all you need to know to program these things. If you want plug and play there are multiple libraries to choose from.
Answered by BG344213471 on 31/08/2022Helpful (0)
0
Q:
I can choose the color of the matrix or only send it in a single color?
I can choose the color of the matrix or only send it in a single color?
Use the MD_MAX72XX library. With the device set to: #define HARDWARE_TYPE MD_MAX72XX::ICSTATION_HW. If you don't change that line in the examples, the characters are mirrored. Use the MD_Parola library (also) for even more functions. All sketches have to include that line, the default is Parola hardware.
Use the MD_MAX72XX library. With the device set to: #define HARDWARE_TYPE MD_MAX72XX::ICSTATION_HW. If you don't change that line in the examples, the characters are mirrored. Use the MD_Parola library (also) for even more functions. All sketches have to include that line, the default is Parola hardware.
Answered by Strider on 28/11/2018Helpful (0)
Ask a Question
1.You can contact the customer service. for any question regarding the product.
2.Ask the question in English to get answer faster.